|Warranty:||1 Year||Type:||Die-cutting Machine|
|After-sales Service Provided:||Engineers Available To Service Machinery Overseas,Video Technical Support,Online Support,Free Spare Parts,Field Installation|
Type 500 Spine or Grid die casting machine used to produce tubular positive spine which length less than 500mm. Details of 500 spine making machine: firstname.lastname@example.org
Type 500 Lead Acid Battery Positive Plate Spine/Grid Die Casting Machine used to manufacturer tubular grids which length shorter than 500mm. The machine is manual operated. It consists a die casting machine, a grid casting mold, a cutting machine.
1.Grid length, 2v 15tube, single, L≤430mm, double, L≤470mm
2.Grid length, 12v, single, L≤300mm, double, L≤210mm
A. Production capacity: ≥2 shot per minute
B. Power supply: 380V, 3P, 50Hz or customized
C. Electricity consumes : 55kw
D. Pump motor: 15kw
E. Mould heater: 0.4KWX4=1.6KW
F. Lead pot heater: 6KWX6=36KW
G.Nozzle heater; 0.35KWX6=2.1KW
H.Mould lifter motor : 0.37KW =0.37KW
I. Lead melting pot capacity :1800 kg
J. Machine size (LWH):4100*1000*1900MM
K.Machine weight: 4T
Type 500 spine/grid die casting machine need one person to operate casting machine and cutting machine.
Electricity, cooling water, compressed air, lead fume ventilation pipe for exhaust.
(Technical parameters: power 50kwh ,compressed air 0.1m3/min, 0.6MPa; water consumption 240l/h)
As die casting machine is horizontal type, the cement floor must flat. Concrete deepth at least 100mm.
Cooling water is used to cool the mould and the oil. Normal water, circulating water is allowed. If the die casting grid has flash and burr, need to increase the die locking pressure . The locking pressure should be adjusted slowly. Same time the system pressure also be adjust. And to find the appropriate value.
Lead pot consist: lead pump, injection cylinder, heating pipe, pot body, and heat preservation layer, etc.
Lead pot capacity:1800kg
The mould locking system consist of locking cylinders, the mold release cylinders and the mould plate.
Mold material:H13 steel
Mold size: 35 thick X360 wide x620 long mm
Place the mould to the fixed position with lifting tool, fixed the mould, connected with the heating pipe and the thermocouple.
Spine cutting machine drives by compressor. Cutting blade material is T8 or 45# steel.
1.Before work, to check the reliability of the connection of water, electricity, etc. of equipment.
2.Open power control cupboard door, close the main power switch and the separate switch;
3.Start the power, select manual state to check mold moving, mold locking action.Don't oprate injection action at this time.
4.Turn on the lead pot heating switch. The lead pot heating takes about 2.5 hours.
5.Lead pot temperature heated to about 350 degrees, then to heat the mold and nozzle.
6.When all the temperatures are up to the required values, start the trial run of the equipment. Before starting the machine, check whether the lead melts at the nozzle with steel bars. Manual operation , check the machine. If there is no fault, automatic cycle can be started.
7.After grid picked up from die cavity, it is necessary to check and clean the impurities in the mold.
If the casted grid is not full, has flash or burr, the system pressure and the injection pressure should be adjusted. The general adjusting rule is that the injection pressure should be increased when the grid is not full, the locking pressure should be increased when the flying edge is unsatisfied.
8.When the grid sticks in the mould cavity, the mold release agent should be used.
9.when the mold nozzle temperature is too high, damp cloth or spray gun can be used to cool nozzle localized.
Die casting Machine is metallurgical equipment, it is working in high temperature and adverse impact environment. Regular maintenance and repair of equipment is necessary, the specific matters are as follows:
The common failures of hydraulic system of the equipment are:
Pressure is insufficient or unable to fall
|Overflow valve blockage||
|The reversing valve does not act and the middle position is not locked.||Reversing valve clogging||Clean|
|High oil temperature||
Low cooling water pressure or high temperature.
Relief valve not unloading
Increase the pressure
Check relief valve
|Oil leaking||The seal is broken or loosened.||Remove and replace gaskets|
|Oil leakage of mould moving cylinder||Leakage is sealed or broken.||Replace seal or cylinder.|
|The motor or pump has a lot of noise.||
Motor bearing damage
Oil pump damage
Repair or replace
|Low oil level||Add oil|
|After adjustment, the grid can not be fill full.||Insufficient pressure on accumulator||90 Mpa for nitrogen storage of accumulator|
|System without pressure||The unloading switch is not closed.|
When the hydraulic system is repaired, the unloading switch in front of the accumulator must be loosened. And the oil in the system must be discharged into the oil tank to avoid oil spilling out. Please confirm that the switch is off before turning on.
-Check the tank oil level frequently.
-Check the oil temperature;.
-Check the operation of each valve.
-Check oil leakage in pipes and cylinders.
First use the equipment, change the oil once a half year, and clean up the system every year.
Domestic and international famous brands are used in electrical systems. Some parts are easy to break down for frequent use.
The main failures are as follows:
|An action does not move.||
The trip switch is not in place or damaged.
Intermediate relay damage
Electromagnetic valve relay damage.
|Adjust position replace|
|The temperature of the lead pot, nozzle is increased, or the temperature is slow.||
Heating tube damage
Damage of thermocouple
Wrong type of thermocouple.
Thermocouple line reverse.
Failure of temperature controller.
Replacement of corresponding models.
Replacement of temperature controller.
|Program does not run or program chaos||PLC fault||Maintenance or replacement|
Type 500 Battery Positive Spine/Grid Pressure Die Casting Machine
More information and price of Type 500 Battery Positive Spine/Grid Pressure Die Casting Machine, Mould or Production line, please contact us: email@example.com
· Battery Spine Die Casting Machine
· Cold Chamber Die Casting Machine
· Hot Chamber Die Casting Machine
· Vertical Die Casting Machine
· Aluminum Die Casting Machine
· Magnesium Die Casting Machine
· Auto Parts Die Casting Machines
· Kitchen &Household Parts Die Casting Machines
· Lamps Light Parts Die Casting Machines
· Electric Vehicle Spare Parts Die Casting Machines
· Hardware, Jewelry, Clothing Accessories Die Casting Machines
· Tel-Communication Equipment Parts Die Casting Machines
· Garden Machinery & Electric Tools Parts Die Casting Machines
· Lead Acid Battery Terminal Bushing, Battery Positive Spine Grid Die Casting Machines
· Fishing Sinker Die Casting Machines